Recent content by marshall2553

  1. M

    FM3 Firmware Version 8.00 beta 1

    I haven't tried in Axe Edit, just the front panel. I kind of prefer the behavior on the Axe Fx because IMO those values are a better sounding starting point with a lot of mics/cabs than Cap / 0 cm. But I don't know which is "correct".
  2. M

    FM3 Firmware Version 8.00 beta 1

    Not a bug per se, but an inconsistency between the FM3 and the Axe Fx. After resetting the cab block, the default DynaCab mic position and distance are 0.0 on the FM3, but on the Axe Fx they default to 5.00 and 4.80 respectively. Not sure what the FM9 does, I don't have mine handy right now.
  3. M

    Axe-Fx III Firmware 25.00 Release

    Yeah, I just checked the Recto Slant using Axe Edit and it seems to be working. There is an audible difference when toggling between Dynamic 1 and 2.
  4. M

    Axe-Fx III Firmware 25.00 Release

    I checked several cabs and I definitely hear a difference between Dynamic 1 and 2. DynaCabs are updated independently of the DSP firmware, so it's probably unlikely that this update broke them. Were you on a clean or dirty preset when you tried this? The difference between the mics would be...
  5. M

    Axe-Fx III Firmware 25.00 Release

    The Class-A 30W Brilliant model is 💯 I've been playing a lot of STP lately and it's so easy to dial in Dean's tones from Purple and Tiny Music with this model.
  6. M

    Axe-Fx III Firmware 25.00 Release

    Weird. I just tested again and tails are cut off for me if I set it to mute output.
  7. M

    Axe-Fx III Firmware 25.00 Release

    Are you sure? I noticed this in the beta, but can't repro it in this release.
  8. M

    Not a Bug Tuner stopped working

    Check the Source setting on the tuner's config tab and make sure it matches the input you're using.
  9. M

    Which single amp channel to do it all?

    For me it's the Wrecker Express and Liverpool. I dial the amps in for a lead tone and then roll my guitar volume down to 1/2 or 3/4 for clean and crunch.
  10. M

    Axe-Fx III Firmware 24.04 Release

    Yeah. I never really bonded with the D60 models before this update, but I'm really liking both now. I could probably use D60 Less for 90% of the stuff I play and be pretty happy.
  11. M

    Axe-Fx III Firmware 24.03 Release

    York Audio has a Marshall V30 pack that sounds great. FWIW, I don’t think the matching cab thing is that big of a deal. I played my Jubilees through a stock cab that I assume had T75s and another with Greenbacks and they sounded fine. Since the B/M/T controls actually do something on the...
  12. M

    Fryette D60 More not enough gain?

    I had a Pittbull a while back. It was a really cool, but very unforgiving amp. It had tons of gain, but somehow seemed to have very little compression or saturation. I don’t know how to describe it other than dry and stiff. I guess it’s the signature Fryette sound because the D60 I tried was...
  13. M

    Axe-Fx III Firmware 24.02 Release

    I sold my last Jubilee several years ago, so I can’t directly compare. But the model sounds really good. I do wish we could get models of the clean and rhythm clip modes.
  14. M

    How to make lower gain Plexi pre set sound full?

    Lower the value of the bright cap. Or raise the treble gain and lower the input trim to compensate. The bright cap has less effect the higher your treble gain is set.
  15. M

    FM 3 voltage pulse issue

    Weren’t some people seeing the I/O lights on the FM3 light up when it was off but connected to USB? Maybe try disconnecting the USB cable and see if it stops.
See more
Back
Top Bottom