Recent content by LarsB

  1. L

    Anyone have an electric car?

    I've been driving electric for almost four years now. First a Tesla Models S for a little less than a year, and then Tesla Model X for the last three years. Works great for me. The Model S is better looking and with a better range, while the Model X is a bit more practical for me in daily use...
  2. L

    Is there a TABLES of default values?

    The editor config has the default values, but they are in raw form and not very easy to read for anyone .. human. :lol: You can place a block in the editor and it will show you the correct default values though, that's probably the easiest way at the moment. Lars
  3. L

    Drive Type Label Issue

    It doesn't make sense to move the thread as it contains more than one issue. The part I'm saying is not an editor issue is that Claudel & Frankiev thinks the TS 808 MOD and Oct Dist models have been swapped in the firmware. I have no idea if that is the case or not. The editor is configured to...
  4. L

    Firmware 6.10 bug?

    Looks like it works slightly different now on my Standard, it works if you press enter on an existing effect / shunt, but not if you do it on an empty slot. Edit: Same on the Ultra. Not sure if it's always been this way or not. Also noticed how pressing Exit works on existing shunts & effects...
  5. L

    Help w/ GCP setup

    A MIDI program change message has a range of #0 - 127, where #0 is the first preset. If you are sending #1 and expect to see the first preset you are sending the wrong program change message. The display offset in the Axe-Fx is just that, a *display* offset, in terms of midi the first preset is...
  6. L

    Worrysome, Ultra frozen. two times.

    Yes you did! There is a huge difference between a MIDI interface occasionally corrupting data and not being able to send data correctly at all. There is also a huge difference between an interface corrupting data on *your* system with the drivers *you" are currently using and doing the same on...
  7. L

    Worrysome, Ultra frozen. two times.

    Do not put words in my mouth. I haven't said anything about those devices. You might want to read the troubleshooting guide, there are some bits in there that might help you understand MIDI corruption. You can use MidiOX, but you HAVE TO get the data BEFORE they are transmitted through ANY...
  8. L

    Worrysome, Ultra frozen. two times.

    Don't do it by blaming it on the editor... Lars
  9. L

    Worrysome, Ultra frozen. two times.

    It is NOT because of the editor. The editor sends the correct values. It is because: 1) MIDI corruption occurs because your MIDI interface is not able to transmit the MIDI data correctly to the Axe-Fx 2) The Axe-Fx does not guard against out of bounds errors caused by corrupted MID messeages Lars
  10. L

    Reworked Patches (Blackface, Deluxe & JCM800)

    Whaddya mean, the editor has had support for the CAE models since they were introduced. 8-) Lars
  11. L

    Novation Zero SL -- Do you? would you ?

    It will not work in any way with the Axe-Fx Editor or Axechange. It will work directly with your Axe-Fx for the external controllers, but it will limited by what can be controlled on the Axe-Fx. Most likely it will not work like you think it will, and you will be bummed if you buy it. Lars
  12. L

    The new "CA3+ Rhythm" amp in v6.03

    Nice! Lars
  13. L

    AxeChange: 6.0 cabs wanted

    Try again now, should be working again. Let me know if you run into any other problems! Lars
  14. L

    AxeChange: 6.0 cabs wanted

    Doh! I'll fix it. Lars
  15. L

    AxeChange: 6.0 cabs wanted

    AxeChange should now be functional with the 6.0 cabs, cabinets are most welcome. The editor will be integrated with the cabinet section of AxeChange as soon as I find the time to implement it, should make it a lot easier to preview cabinets. Lars
See more
Back
Top Bottom