• We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

    Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by hm269

  1. H

    Year and half later; still not happy with Axe-Fx 3

    Leon's (@2112 ) 5 Minute Tones videos are also awesome and you can learn a ton about how to dial in a tone that sits tight in the mix, choose the right cab etc:
  2. H

    Acoustic Simulation using Multi-Band-Compressor and IRs (IRs, blocks and video included)

    I had to convert the WAVs with CabLab lite. When I dragged the WAVs directly into the "Manage Cabs" browser in Axe Edit only the SuhrBridge ones were working. The others gave me a big delay/lag when playing and the plot was just a flat line when viewed in the cab block align page. But when...
  3. H

    Axe-Fx III Firmware Release Version 12.04

    I would guess this is the "Cathode Resistance" value on the power amp page in Axe Edit (on the hardware it would then be "P.A. Cathode Resistance" in the Advanced section of the amp block.
  4. H

    Axe-Fx III Firmware Release Version 12.03

    In the cab block it goes to 24dB/oct, but Leon used a PEQ block behind the cab in his last videos. The PEQ filter slope goes to 36dB/oct ;)
  5. H

    Axe-Fx III Firmware Release Version 12.03

    Nah come on, don't you hear the golden clarity in this version? The soundstaging is definitely more focused and musical ;)
  6. H

    Axe-Fx III Firmware Release Version 12.01

    True. And don't edit from the front panel with Axe Edit open. Don't touch it. Don't even look at it...
  7. H

    Axe-Edit III 1.04.02 RC 1

    Yes, Axe-Edit RC1 resets parameters in the Amp block with Firmware 12.01, I noticed this for Speaker Impedance Curve, Bass/Mid/Treble, Input Trim. Probably more parameters are affected. I recommend to close Axe-Edit and use the front panel when editing until it gets updated.
  8. H

    Axe-Fx III Firmware Release Version 12.01

    Yes, I also noticed this. Don't edit your presets in Axe Edit or front panel with Axe Edit open for now. Make sure that Axe Edit is closed when editing until it gets updated.
  9. H

    Axe-Fx III Firmware Release Version 12.01

    Yes, always remember to CLOSE Axe Edit when cross-checking at the front panel 😉
  10. H

    Axe-Fx III Firmware Release Version 12.01

    Ok, I did some further testing. It happens only if Axe Edit is open. It also happens if you just navigate out of the Amp block and back in Axe Edit. So it is a bug in Axe Edit, not in the Firmware.
  11. H

    Axe-Fx III Firmware Release Version 12.01

    Possibly a bug? When I change the Speaker Imp. Curve, XFormer Low and Hi Freq. in the Amp block Speaker page and save the preset it will reset to the Amp defaults when I recall the preset. I tried on front panel and Axe Edit RC1.
  12. H

    5 Minute Tones

    "Yeah, you guys just gotta go next level somehow..." ;)
  13. H

    Axe-Fx IV round the corner?

    "Class-A 30W TE" coming? :D
  14. H

    Axe-Fx III Firmware 10.0 Public Beta

    Coming in Firmware 11: Tube wear. We will have to replace all the tubes in the amp models after some time. They can be bought in the In-Device-Shop for a small amount ;)
  15. H

    Axe-Fx III Firmware Version 9.01

    Everyone ist busy playing, no time to make a video ;)
Top Bottom