Recent content by Finnster

  1. Finnster

    Whammy and/or Wah per scene

    Thank you! I will try this. And can I assign the MUX block to switch its input with a switch or scene?
  2. Finnster

    Whammy and/or Wah per scene

    Using a spring loaded Mission expression pedal. I have it set to auto-on for the wah. Can I use the same setting for the pitch-shift/Whammy? Meaning one scene the wah is active and on another scene the whammy effect is active. I must be doing something wrong because they both engage. I’m...
  3. Finnster

    Fractal Audio DRIVE models: Shred Dist (based on Marshall Shred Master)

    The FX8 doesn’t have all those controls. Just a tone knob instead of a contour. Just Drive, Tone, level.
  4. Finnster

    Does anyone have video/pictorial tutorial of the 7 cable method?

    As an option for a wet dry setup I have been using a Marshall Mini Jube and a PRS MT15. I run the MT15 in 4CM and the Marshall dry. I guess it’s a 5CM:-). But I also use bouts amp relay outs for channel switching. They sound amazing together. I use it at rehearsal but not really practical...
  5. Finnster

    Switching/Relay question

    Marshall DSL20HR. I don’t need to turn the loop off with the FX8. My concern is that I won’t be able to keep it on since it’s defaulted to always off unless the Marshall 2 button FS is used. I think I could work around it with a Y TRS splitter and run 2 TS cables from the FX8 relay. But I...
  6. Finnster

    Switching/Relay question

    i am considering a new amp. The amp I’m looking at comes with a 2 button footswitch using a TRS cable. One button changes the channel and the other turns on the effects loop. The effects loop is defaulted to “off”all the time unless engaged with the footswitch. I know this by testing the amp...
  7. Finnster

    FX8 Edit connection issue

    I haven’t able to backup my FX8(other than 1 preset at a time) with FractalBot. I keep getting a timeout message. Anyone else have this issue since the latest update?
  8. Finnster

    Good Synth Blocks/Presets for FX8

    Nice work! Is this on Axe Exchange?
  9. Finnster

    Noise gate and sustain

    Disregard my -100 comment. That is on Axe Edit. It says “off” on the unit.
  10. Finnster

    Noise gate and sustain

    Thanks. I do remember on my AxeFx II when I turned the threshold all the way down it would say “off”. On my FX8 it doesn’t read “off” it reads -100. Also, on the global settings my Noisegate offset is a 0 dB. I think that’s where it should be.
  11. Finnster

    Noise gate and sustain

    If all values are set fully counter-clockwise is the gate essentially off? Also, I messed with the threshold and I’m still losing sustain, tested against bypassing the unit. I’m using the “intelligent” setting. Can anyone post their settings that work for them? Also, would the pad input for...
  12. Finnster

    Noise gate and sustain

    Thanks, I will try that
  13. Finnster

    Noise gate and sustain

    Has anyone had an issue with the input gate affecting sustain? Most of my presets are at the factory default with regards to the input gate. I'm a bit ignorant when it comes to setting up the values on each parameter so I pretty much have left it alone. I do have a substantial loss in sustain...
  14. Finnster

    Library of effects and a new computer

    Solved....I found it under documents>FX8Edit>Blocks right before you sent this. Thanks!!!
  15. Finnster

    Library of effects and a new computer

    I switched from my old MacBook Pro to a newer one. My library of effects that I use frequently is now gone. I don't want to start over......YIKES! Are there any savy OSX users that would know where they are in my old computer so I can transfer them over to my new one? I tried loading FX8...
Back
Top Bottom