We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

Please give yourself a refresher on the forum rules you agreed to follow when you signed up.

Recent content by Fatjac

F
Axe-Fx III Firmware Release Version 19.05

Regarding scene ignore...I think that I understand the concept &, as always, I'm grateful for the continued improvement to the Axe FX3 et al but perhaps I am also missing the point. If it's necessary to keep say an amp on channel 1 in every scene then why not simply set it to that for every...
- Fatjac
- Post #201
- Mar 15, 2022
- Forum: Axe-Fx III Discussion
F
Question about recording with USB connection to mac computer

I'm probably wrong but do you have to make the FX3 the master for the sync at 48k?
- Fatjac
- Post #3
- May 6, 2021
- Forum: Axe-Fx III Discussion
F
Axe-Fx III Firmware Release Version 16.00 "Cygnus"

Fab uuu lous!
- Fatjac
- Post #18
- Apr 21, 2021
- Forum: Axe-Fx III Discussion
F
Presets MASTER THREAD - AustinBuddy's 1400+ NAKED AMPS TonePack for firmware Cygnus X2

Thanks. It's just down to the way that I set my presets. I think this will work if I just use the Amp block to mute rather than using the Cab block too. I can see why you have done it that way but I wasn't getting any sound! It's all part of the steep learning curve! Great update and thanks...
- Fatjac
- Post #1,255
- Feb 4, 2020
- Forum: Vendors
F
Huge difference between FR/FR and PA

Could it be over or under signal strength? I'm thinking -10db/ +4db. PA channel gain too high/ too low?
- Fatjac
- Post #7
- Feb 4, 2020
- Forum: Axe-Fx III Discussion
F
Presets MASTER THREAD - AustinBuddy's 1400+ NAKED AMPS TonePack for firmware Cygnus X2

Thanks. I thought it would be but I just couldn’t find it. I have done now it is on the Room Air page... not an obvious place to me but it’s probably down to limited possibilities of where to put it. I duuno. I started using OP1 with a permanent cab for FOH and headphones leaving OP2 to go to...
- Fatjac
- Post #1,249
- Feb 3, 2020
- Forum: Vendors
F
Presets MASTER THREAD - AustinBuddy's 1400+ NAKED AMPS TonePack for firmware Cygnus X2

Hi, I wonder if someone might answer a question for me please? At present I am using a SS power amp with a 2x12 Orange cab. It's therefore best to switch off cab modelling but I occasionally wear headphones so I usually just bypass the cab block when I try a preset. The I do this in one of the...
- Fatjac
- Post #1,246
- Feb 3, 2020
- Forum: Vendors
F
Presets MASTER THREAD - AustinBuddy's 1400+ NAKED AMPS TonePack for firmware Cygnus X2

Again, many thanks for taking the time to write such a detailed response. Believe me it is very much appreciated!
- Fatjac
- Post #1,239
- Jan 28, 2020
- Forum: Vendors
F
Axe-Fx III Firmware Release Version 12.00

Amazing! I can't keep up...so much to tinker with. I just get used to one thing and the next appears! Thanks.
- Fatjac
- Post #64
- Jan 28, 2020
- Forum: Axe-Fx III Discussion
F
Presets MASTER THREAD - AustinBuddy's 1400+ NAKED AMPS TonePack for firmware Cygnus X2

Wow! Your reply is as detailed as the Naked Amps themselves! Many thanks. I like the idea of your method. I already have Bank A mostly blank. My own favourite presets occupy presets 1-20 so I could move them up to higher slots leaving 1-20 clear. I retained the original, but updated recently...
- Fatjac
- Post #1,228
- Jan 28, 2020
- Forum: Vendors
F
Presets MASTER THREAD - AustinBuddy's 1400+ NAKED AMPS TonePack for firmware Cygnus X2

Hi, I have a question. I'll start by saying that I have watched your excellent videos & tried to read what I can find about the subject but although it could be there, as yet, I haven't found the answer. I have the Naked Amps pack. Like a few people I use Bank A for my favourites & dragging in...
- Fatjac
- Post #1,226
- Jan 27, 2020
- Forum: Vendors
F
5 Minute Tones

Thanks Rex. I'll experiment later. Just something that I hadn't come across before...
- Fatjac
- Post #257
- Jan 16, 2020
- Forum: Axe-Fx III Discussion
F
5 Minute Tones

Thank you both for your replies. It's still not quite making sense. I'll have a play with it later & see what I can make of it!
- Fatjac
- Post #255
- Jan 16, 2020
- Forum: Axe-Fx III Discussion
F
5 Minute Tones

Great sounds using the Plex delay. Please tell me what is the purpose of putting it in parallel with a shunt? My simple brain says that doing so will cause the sound to take the most simple path and ignore the delay. (I have read the linked post above but it doesn't answer my question). I can...
- Fatjac
- Post #252
- Jan 15, 2020
- Forum: Axe-Fx III Discussion
F
Axe-Fx III, PS-2, Cab Settings Question

I have no wish to hijack the thread but could you clarify the above statements for me please? If the amp is transparent...select restive load. Does that hold for running an SLA solid state amp & real 2x12 cab then? I have been using the impedance curves thus far & I am very pleased with the...
- Fatjac
- Post #3
- Dec 11, 2019
- Forum: Axe-Fx III Discussion