Recent content by CheapEdge

  1. CheapEdge

    Bug? Ghost blocks in FM-9 editor

    Update 2024-02-12. I have just installed FW 6.0 and Editor version 1.02.09. Upon installation of the new Editor I followed the advise of some of the members below to completely remove the earlier version and only then install the new version. Also, following the advise in the release note from...
  2. CheapEdge

    Bug? Ghost blocks in FM-9 editor

    Hi, I know for sure that this has been reported before, but I can't find that thread anymore, sorry. I installed editor 1.02.06, and the release note says "ghost blocks that occasionally appeared when the unit was disconnected" have been solved. Now, I've had ghost blocks since 1.02.05, but not...
  3. CheapEdge

    FM9 Firmware Version 5.00

    I have the same problem with these ghost blocks and it happens randomly to all my presets. Seems to happen mostly when I step quickly through my setlist, which shouldn't be a problem. Might be related to a rather long USB-cable I'm using (10 meters), but for the rest it works and I didn't have...
  4. CheapEdge

    FracTool - for power users only

    I see ... thx for your quick reply. Actually I have no idea with which version the Axe2 presets were made, but for sure my Axe3 is not on 1.xx anymore for a long time. So, that explains it and if I understand it correctly now there's no hope Fractool will ever do what I hoped, is that right? And...
  5. CheapEdge

    FracTool - for power users only

    Hi Al, hi All, Over the last weeks I've been experimenting with the Fractool. Tried to convert about 5 presets from Axe2 to Axe3. Also three from FM9 to Axe3. Unlike most users who report success here I've only achieved badly damaged presets in my Axe3. Examples: delays with weird settings...
  6. CheapEdge

    MIDI 2.0

    Well, have a look at this and you get an idea of what we may expect. https://www.midi.org/articles-old/the-midi-manufacturers-association-mma-and-the-association-of-music-electronics-industry-amei-announce-midi-2-0tm-prototyping Cheers, Rob
  7. CheapEdge

    MIDI 2.0

    You can now see it, pal ... :-) https://www.midi.org/articles-old/the-midi-manufacturers-association-mma-and-the-association-of-music-electronics-industry-amei-announce-midi-2-0tm-prototyping
  8. CheapEdge

    Axe-Fx III Firmware Version 2.05

    Ah, thx!
  9. CheapEdge

    Axe-Fx III Firmware Version 2.05

    Just a question, so not specifically related to 2.05 release, bit I did not know where else to put it. Question: I just read that the Midi 2.0 spec has been agreed upon and now various suppliers will start testing. I wonder, what are the plans for the Axe FX-3? Would it be possible at all to...
  10. CheapEdge

    The AxeFX3 is superb!

    The AxeFX3 is superb!
  11. CheapEdge

    Axe-Fx III Firmware Version 2.03

    Aha ... thanks ... hmm, well, that explains it, obviously. In that case I have an item for the WISHLIST (guess what ...): can we have MIDI THRU, SCENES MIDI output and SEND PC also sent over MIDI-over-USB? Explanation: I have "other equipment" that is connected through MIDI-over-USB. And I...
  12. CheapEdge

    Axe-Fx III Firmware Version 2.03

    Update 20181209. OK, I'm completely stuck now. Hairpulling, head against the wall - you know what I mean ... Checked all my MIDI settings in SETUP MIDI/REMOTE, carefully checked all settings and the explanations in the manual (version 2) and I could not find any setting or reason why no MIDI...
  13. CheapEdge

    Axe-Fx III Firmware Version 2.03

    Ok, good to know. So, what do you think I should do now? Ports seem to work fine, because Axe Edit works ok. Am I missing anything? Should the MIDI SCENE block be connected to anything on the grid?
  14. CheapEdge

    Axe-Fx III Firmware Version 2.03

    Hi! Question. Just for a bit of experimentation I have put the MIDI SCENE block on my grid, put some CC-controls in there on two scenes, connected good old MIDI-OX for monitoring purposes, switched between the two scenes and ... nothing ... not on the MIDI-USB and not on the DIN connector :-(...
  15. CheapEdge

    Tempo randomly syncs to rising and falling edge of midi

    Thanks, I'll try that and yes, that would be a nice improvement.
Back
Top Bottom