Recent content by bluesk165

  1. bluesk165

    I have a question about FM9's per-preset footswitchs

    For example, in FM9's Scene mode, if I assign Scenes 1, 2, 3, and 4 to footswitches 1, 2, 3, and 4, and Chorus to footswitch 5. Is there a way to turn chorus on or off with footswitch 5 on selecting any of the four scenes? Thanks so much !!!
  2. bluesk165

    Drive block question

    Thanks for always kind your answer!! What I really want to know is the Fractal FX8's range of "the low end and high end". Because they don't say Frequency Values, they just say "Bass". Generally The frequency range is shown in the table below. Sub-bass 20 to 60Hz Bass 60 to...
  3. bluesk165

    Drive block question

    Hi, Friends The following article is from Drive section of FX8 manual. “Bass / Treble – These adjust the low end and high end from ± 12 dB.” In the above article, What exactly does the low end and high end mean? Thanks.
  4. bluesk165

    IN [POST] = Balanced Cable.............

    Thanks for your information !!!
  5. bluesk165

    IN [POST] = Balanced Cable.............

    Every time you help not only me also everybody. I recently bought an Orange rocker 32 combo amp, which is a STEREO Amp so I'm very confused about matching it with the FX8. Thanks a lot.
  6. bluesk165

    IN [POST] = Balanced Cable.............

    Hi, Users The cable used for the IN [POST] of the FX8 is labeled balanced, does this mean TRS on both the FX8 and the amplifier side? Thanks a lot !!!!
  7. bluesk165

    About "block library" on FX8-Edit

    Thanks for your detailed answer !!!
  8. bluesk165

    About "block library" on FX8-Edit

    HI, FX8 friends, If I use EDIT to save a drive block named "My drive", then the "My drive" block automatically load when I load a preset that contains this block? However, the name does not appear in the block library at the bottom left of FX-8 Edit. Thanks
  9. bluesk165

    I have started WET/DRY and have many question

    Hi, F friends, Just tried a Wet/Dry setup with 2 amps and the Black Star Studio 40 with 4CM and Fender Deluxe with a humbuster cable from the Right pre out FX8 for Dry. Now, it works very well but still there are so many question as following, 1. For post effects, setting parallel? or serial...
  10. bluesk165

    TRS Cable for IN [POST] L/R

    Thanks a lot every time.
  11. bluesk165

    TRS Cable for IN [POST] L/R

    Hi, Friends? I hope to make wet / dry rig recently. And have a question for I/O on FX8 manual as following, ㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡㅡ  IN [POST] L/R – (Balanced 1/4” Tip-Ring-Sleeve Jacks) Connect the FX LOOP SEND of your amplifier (or the output of your separate preamp) here...
  12. bluesk165

    4CM and the cables

    Anyway thanks a lot.
  13. bluesk165

    4CM and the cables

    #4 One more thing, What is that mean "BALANCED" at under IN POST?
  14. bluesk165

    4CM and the cables

    Thanks a lot.
  15. bluesk165

    4CM and the cables

    fx8 Friends How are you? I want to do 4CM using my own multi-cable. Is it correct to connect like the attached picture? Of course, TRS-TS cable is a Humbuster.
Back
Top Bottom