1. We would like to remind our members that this is a privately owned, run and supported forum. You are here at the invitation and discretion of the owners. As such, rules and standards of conduct will be applied that help keep this forum functioning as the owners desire. These include, but are not limited to, removing content and even access to the forum.

    Please give yourself a refresher on the forum rules you agreed to follow when you signed up.
    Dismiss Notice

Bakerman's Recent Activity

  1. Bakerman replied to the thread Recording DI track - Axe FX 3 is NOT the main interface!.

    I think you'll need to reduce the DI signal by 20 dB. Also realize any input gating would be applied to the DI with that routing. You...

    Feb 22, 2019 at 2:06 PM
  2. Bakerman replied to the thread Connect Two MFC101 in Serie.

    MFC doesn't have MIDI thru function. The only thing it responds to at MIDI In is PCs for remote MFC preset selection.

    Feb 22, 2019 at 9:55 AM
  3. Bakerman replied to the thread Axe-Fx III Firmware Version 3.02 Public Beta.

    It's voltage with any other percentage level control (volume block, mixer block, various feedbacks...) so power would be an unusual choice.

    Feb 20, 2019 at 6:18 PM
  4. Bakerman replied to the thread Axe-Fx III Firmware Version 3.02 Public Beta.

    6 dB

    Feb 20, 2019 at 5:42 PM
  5. Bakerman replied to the thread Possible Bug: Volume Block level when the FC/Expression pedal is not connected.

    Which source are you choosing at the volume block's volume modifier menu? I'm wondering specifically whether you're selecting "FC Pedal...

    Feb 20, 2019 at 10:42 AM
  6. Bakerman replied to the thread Help with an external footswitch?.

    Yes, but that sounds like how the OP had it set in post #1. The problem scenario is described accurately in post #21. Avoiding it would...

    Feb 20, 2019 at 9:48 AM
  7. Bakerman replied to the thread Wah settings, config...again.

    Try a "position" autoengage option instead of "speed". Speed requires a certain rate of change (pedal speed) to engage, which might not...

    Feb 20, 2019 at 9:32 AM
  8. Bakerman replied to the thread Pitched Based Gate.

    This wouldn't remove individual notes from chords. I'm not sure if that's what the OP is describing. With single notes it's possible,...

    Feb 20, 2019 at 9:04 AM
  9. Bakerman replied to the thread Help with an external footswitch?.

    This would be the same as using a switch port. A preset can load any value for a parameter with PC reset enabled, but if the switch is...

    Feb 19, 2019 at 4:32 PM
  10. Bakerman replied to the thread Re-Amping previously recorded dry tracks.

    Reduce DI track level or Axe input/gate block level until a familiar preset sounds like you'd expect (if you had played that guitar...

    Feb 19, 2019 at 2:55 PM
  11. Bakerman replied to the thread Need help with LFO "run" parameter.

    Try assigning an ADSR (once, retrig off, level 100%) to LFO run instead. Adjust decay or sustain time to make it run as long as needed....

    Feb 19, 2019 at 6:23 AM
  12. Bakerman replied to the thread How to use FX loop and output to a separate amp?.

    Actually it's the opposite--adding FX Loop block overrides echo setting. The routing for this would be like the example below. See post...

    Feb 19, 2019 at 5:50 AM
  13. Bakerman replied to the thread How to make that preset?.

    Sounds like "Velvet Sun 2" factory preset, studio & live. LFO rate (0.07 Hz) even seems to match.

    Feb 17, 2019 at 6:49 AM
  14. Bakerman replied to the thread Tone Matching A Modded Amp.

    FYI (unless this changed since Axe II) MV trim and MV have the same effect.

    Feb 17, 2019 at 6:33 AM
  15. Bakerman replied to the thread Need to control my JP2C with my MFC!.

    An MFC general-use IA can send 2 CCs, 1 PC and up to 5 more basic (PC, CC, note on/off) 3-byte messages as custom data if needed. I'm...

    Feb 16, 2019 at 6:54 AM