Axe-Fx II Firmware V12.00 Up

FractalAudio

Administrator
Fractal Audio Systems
Moderator
NOTE: 12.01 has been released here:
www.fractalaudio.com/downloads/firmware-presets/axe-fx-2/12.0/axefx2_12p01.zip

*******************************************************************************

12.00

Added two “Scene Controllers”. These controllers have a constant value that is programmable per scene. The controllers are accessed via the Control->Scene menu. These controllers can be used to control a parameter such that it has a different value in each scene. For example, Scene Controller 1 might have a Scene 1 value of 10% and a Scene 2 value of 20%. This controller can be attached to Reverb Mix, for example, which would give a higher Reverb mix in the second scene compared to the first scene.

Improved diode models in Drive block. This affects Drive types that use the GE Diode, SI Diode and new LED Clip Types.

Added LED Clip Type to Drive block (see above).

Added “FAS LED-Drive” Drive model.

Added “Tube Drv 4-Knob” Drive model based on a “4-knob” Butler Tube Driver. The existing “Tube Driver” model has been renamed “Tube Drv 3-Knob”.

Improved Amp block power supply current draw modeling which improves “feel”.

Improved Amp block phase-inverter-to-power-tube-grid interaction modeling which improves transient response resulting in faster attack. This also improves the clarity of notes especially when using heavily overdriven power amp settings.

Added Global “Modeling Version” parameter to select between Version 11.xx or Version 12.xx power amp modeling.

The Amp block “Grid Modeling” parameter has been renamed and repurposed. The new name is “Modeling Mode” and offers the following choices:
1. Authentic – Replicates a tube amplifier with the utmost accuracy.
2. Grid Cond Off – Turns off grid conduction modeling in the power amp simulation. This reduces blocking distortion.
3. Smooth – Sets Triode Hardness to the minimum value essentially creating an ideal preamp and turns off grid conduction modeling in the power amp. This removes most of the “nasty” distortion that tube amps create.
4. Ideal – Removes most of the “warts” from the modeling which includes grid conduction, output transformer distortion, bias shifting and AC power supply modeling. Supply sag, screen voltage effects and crossover distortion are still modeled.
5. Ideal/Smooth – Same as #3 but also sets Triode Hardness to its lowest value. This is in essence an ideal preamp plus an ideal power amp.

The audibility of these settings is dependent upon the particular amp model and various parameters. The use of these modes in conjunction with other parameters can yield idealized tones not achievable with real tube amps.

The first two choices duplicate the previous behavior of the deprecated “Grid Modeling” parameter so no changes are required to existing presets.

Note that when “Ideal” is chosen the global Modeling Version parameter is irrelevant.

Added “5F1 Tweed” amp model based on a Fender Champ. This particular amp exhibits a unique breakup characteristic due to its single-ended design and simple circuit.

Added “Wrecker 2” amp model based on a Trainwreck Express.

Added “Two Stone J35 2” amp model based on a Two Rock Jet 35 with the Preamp Bypass switch off. The existing “Two Stone J-35” model has been renamed “Two Stone J35 1”.

Added “Wrecker 2” and “Skyline Deep” tone-stack types to Amp block. Skyline Deep is the Skyline tone-stack with the Deep switch engaged.

Added “ODS-100 Lead 3” amp model based off a non-HRM Dumble with the Preamp Bypass switch off.

Changed the Amp block Overdrive knob now defaults to 7.5 when selecting an amp model that uses this knob as this is a more typical value.

Added Level control to Enhancer block Classic mode.

Tremolo block now resets LFO when bypassed so that LFO starts at 90 degrees when effect is engaged.

Added Scene indication to main Layout page.

Fixed Delay block Ping-Pong type mix level twice what it should be.

Fixed activating Hold in Delay block causes swelling in echos.

Fixed Reverb clicking for Room, Catherdral and Studio types when size is greater than 85.

Fixed Pitch block Arpeggiator where certain scale degrees would sound the root instead of the desired harmony.

Fixed corrupted user cabinet data can cause erratic behavior.

Fixed corrupted MIDI streams can cause crash.


*******************************************************************************


I've been very busy with many things and apologize if your pet amp/pedal/wish didn't make it into this firmware.

Axe-Edit support to follow shortly.
 
Nice! I'm happy with firmware 11 but still curious to try out this "Grid Modeling". Thanks Cliff!!

<---- Guess it's time to update my avatar, eh? :encouragement:
 
Wow.......amazing list of improvements. Thank you SIR.......and I do mean that most sincerely!
 
wow can really hear the difference in the grid modeling modes with the USA Lead Model
Ideal and Ideal smooth.....wow sounds like 9.02 did very cool
 
Wow Thank you Cliff you Rock !!!! Can't wait to get my Axe back it's in the shop !!! You guys are the best !!!
 
Modeling mode is really neat!! Is it supposed to show up on Axe-Edit? I'm still seeing the old Grid Modeling switch.
 
Back
Top Bottom